UART1 output test ok
Uart init
Found 1 x 2M flash memory

---RealTek(RTL8181)at Wed Oct 22 04:07:36 EDT 2003 version 2.01
Error led is OnJump to image start=0x80300000...
Error led is Offdisplay on
entering boot loader, turning on display
decompressing kernel:
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
Linux version 2.4.18-MIPS-01.00 (roger@linuxserver.abocom.com.tw) (gcc version 3.0.3) #26 Thu Jan 15 18:11:59 CST 2004
Determined physical RAM map:
 memory: 01000000 @ 00000000 (usable)
Initial ramdisk at: 0x80196000 (1043555 bytes)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/ram console=0 ramdisk_start=0 single
Calibrating delay loop... 204.39 BogoMIPS
Memory: 13356k/16384k available (1479k kernel code, 3028k reserved, 1104k data, 48k init, 0k highmem)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
 unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Serial driver version 6.02 (2003-03-12) with no serial options enabled
ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1
state->flags=00000000
block: 64 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
PPP generic driver version 2.4.1
RealTek E-Flash System Driver. (C) 2002 RealTek Corp.
Found 1 x 2MiB MXIC MX29LV160AB at 0xbfc00000
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 2048)
ip_conntrack (128 buckets, 1024 max)
ip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Bridge firewalling registered
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 1019k freed
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 48k freed
mount /proc file system ok!
serial console detected.  Disabling virtual terminals.
Abocom Gateway System init started:  BusyBox v0.60.1 (2003.12.11-06:16+0000) multi-call binary
flash paramter check
Kill all Syslog Daemon
killall: syslogd: no process killed
set eth0 mac
wlan1: not found
wlan2: not found
wlan3: not found
wlan4: not found
wlan5: not found
wlan6: not found
wlan7: not found
wlan8: not found
length=0?
length=0?
Entering AP MODE
This is 8305SB
before close, nr_free_pages=000007a0
after close, nr_free_pages=000007a0
SIOCGIFFLAGS: No such device
bridge br0 doesn't exist!
bridge br0 doesn't exist; can't delete it
Setup bridge...
Algorithmics/MIPS FPU Emulator v1.5
device wlan0 entered promiscuous mode
device eth0 entered promiscuous mode
NAT2.5 is enabled
br0: port 1(wlan0) entering listening state
br0: port 1(wlan0) entering learning state
br0: port 1(wlan0) entering forwarding state
br0: topology change detected, propagating
This is 8305SB
eth0: Promiscuous mode enabled.
eth0: Promiscuous mode enabled.
br0: port 2(eth0) entering listening state
eth0: Promiscuous mode enabled.
br0: port 2(eth0) entering learning state
br0: port 2(eth0) entering forwarding state
br0: topology change detected, propagating
Entering FIXED IP MODE
fixedip.sh
killall: dnrd: no process killed
ap end
START_FIREWALL
START SNMP
Port:777


BusyBox v0.60.1 (2003.12.11-06:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

# IEEE 802.11f (IAPP) using interface br0 (v1.2)